How to choose the right replacement for a Danfoss Prof 1 joystick?

Joysticks Prof 1 series

Discontinued

Danfoss Prof 1 series joysticks are no longer manufactured and have been replaced by the newer JS1-H generation.

Base dimensions
Screw hole diameter: 5.50 mm
Screw spacing: 90 mm
Base width: 105 mm

Prof 1 joystick base drawing

Show drawing

Joysticks JS1-H series

New model (replacement)

In our e-shop you will find new replacements for the original Prof 1 models, but you need to take a few differences into account.

Base dimensions
Screw hole diameter: 6.00 mm
Screw spacing: 88 mm
Base width: 90 mm

JS1-H joystick base drawing

Show drawing In stock

Find a replacement for your Prof 1 joystick

Enter the product code (e.g. 162F1101) of your original Prof 1 joystick; on the product detail you will then find the corresponding JS1-H alternative.

Doesn't fit? We offer an adapter

For a trouble-free installation of the new JS1-H joystick into the original Prof 1 mounting hole, we offer a special adapter of our own design, made to fit the exact dimensions. Mount the adapter in the original Prof 1 hole and simply fasten the new JS1-H joystick into it.

Adapter from Prof 1 to JS1-H
ID MEC204_1

Adapter from Prof 1 to JS1-H

83,85 € 83,85 € incl. VAT
On request
Note: When using the adapter, the new joystick will sit approx. 2 cm higher than your original joystick.
Note: When using the adapter, the new joystick will sit approx. 2 cm higher than your original joystick.

Proportional function switches

Original Prof 1 series

Some Prof 1 joystick models were equipped with so-called DIP switches, i.e. proportional function switches, which made it easy to invert the proportional functions of the joystick.

New JS1-H series

JS1-H models are no longer equipped with these switches. The functions can, however, be changed electronically using a diagnostic cable.

If your original Prof 1 joystick was equipped with a switch, contact us and we will configure your new JS1-H joystick to work exactly like the original Prof 1 with the function switch.

Different connector

Original Prof 1 series

While the Prof 1 series has a 25-pin D-SUB connector integrated directly in the base, the standard version of the JS1-H has the connector on an approx. 10 cm cable coming out of the joystick base.

New JS1-H series

In addition to the standard 25-pin D-SUB connector, JS1-H joysticks also feature a 6-pin Deutsch connector used for diagnostics and function switching.

Frequently asked questions FAQ

Why can't Prof 1 joysticks be ordered anymore?

In 2026 Danfoss discontinued production of the Prof 1 series. Based on the model number of your original Prof 1 joystick, however, we can in most cases offer a functional alternative from the newer JS1-H series.

Do JS1-H joysticks work the same as the original Prof 1 series?

Yes, the replacement we recommend will work the same as the original joystick. Keep in mind, however, that there are several design (and in some cases functional) differences between the Prof 1 and JS1-H series, described above on this page.

Couldn't find a replacement for your joystick in our database?

Not all older versions of Prof 1 joysticks have a direct alternative.
Send us a photo of your original joystick and we will get back to you.

Need advice?

Call us at
+420 739 290 046

Or write to
eshop@technotrade.cz

Recently
viewed
ID 11007562

On request
  • Basic motor
    OMT
  • Series
    O-series
  • Displacement
    200 cm³
  • Shaft style
    Straight
  • Shaft size
    Dia. 40 mm - M12 tap
  • Mounting thread dimension
    Pilot dia. 125 x 9 mm - B.C. dia. 160 mm - Dia. 14 mm
  • Mounting flange
    4 Bolt - Square
  • Shaft key
    A12 x 8 x 70 mm
  • Port style
    Side ported - offset manifold (4 x M10)
  • Port dimension
    G 3/4
  • Drain port style
    Standard - bearing housing
  • Drain port dimension
    G 1/4
  • Dust seal
    Standard
  • Shaft seal
    NBR - High pressure
  • Seal kit product ID
    151B0113
  • Front bearing
    Tapered roller bearing
  • Rear bearing
    Tapered roller bearing
  • Gear wheel set
    Standard
  • Check valve
    Yes
  • Special features external 1
    Bearing housing - hole for speed sensor
852,69 € excl. VAT
ID 11159855

On request
  • Basic motor
    OMT
  • Series
    O-series
  • Displacement
    160 cm³
  • Shaft style
    Straight
  • Shaft size
    Dia. 40 mm - M12 tap
  • Mounting thread dimension
    Pilot dia. 125 x 9 mm - B.C. dia. 160 mm - Dia. 14 mm
  • Mounting flange
    4 Bolt - Square
  • Shaft key
    A12 x 8 x 70 mm
  • Port style
    Side ported - offset manifold (4 x M10)
  • Port dimension
    G 3/4
  • Drain port style
    Standard - bearing housing
  • Drain port dimension
    G 1/4
  • Dust seal
    Standard
  • Shaft seal
    NBR - High pressure
  • Seal kit product ID
    151B0113
  • Front bearing
    Tapered roller bearing
  • Rear bearing
    Tapered roller bearing
  • Gear wheel set
    Standard
  • Check valve
    Yes
  • Special features external 1
    Label - ATEX
  • Special features internal 1
    ATEX certification
1 305,48 € excl. VAT